How to Change Price Gun Labels (and Load a New Roll)
Changing price gun labels is a short routine. Open the label chamber at the back of the gun, lift out the empty core, drop the new roll in so the labels face the right way, thread the strip under the guide and through the print head, then squeeze the trigger a few times to feed it on.
How do you change the labels in a price gun?
Changing the labels means swapping the roll and re-threading the strip. Press the catch on the back of the gun to open the label chamber, lift the empty core off the spindle, seat the new roll, feed the leading strip under the guide and out through the front, then squeeze the trigger a few times until a label lands on the roller.
The steps are the same on nearly every handheld gun, 1-line or 2-line. The chamber sits at the back or on top, held by a small catch or a hinged cover. Once it is open the path is short and you can see it, so work slowly the first time and remember the route.
- Open the label chamber and take out the empty core.
- Unwind a few centimetres of the new roll so you have a clean leading strip.
- Sit the roll on the spindle with the labels facing up, printing side towards the head.
- Thread the strip under the guide roller and out through the slot at the front.
- Close the cover until the catch clicks.
- Squeeze the trigger three or four times. The gun feeds the blank leader through and the first proper label appears.
The first two or three labels usually come out blank or half printed. That is normal. Peel them off and bin them.
Which way round does the roll go in?
The labels face up as they pass the print head, with the backing paper underneath. Hold the roll so the strip unwinds off the top and the shiny label side points at the ink roller. If you load it the other way round the gun still feeds, but the head prints on the backing paper and every label comes out blank.
Rolls are wound one way for a reason and the gun expects that direction. A blank label is almost always a roll fitted upside down or back to front, not a dead ink roller. Take it out, turn it over, thread it again and test before you blame the gun. If the print is faint rather than missing, the ink roller is the likely cause and those are cheap to replace.
Why will my price gun not feed the new labels?
Most feed faults come down to the wrong label size. Price gun labels are made to suit a gun make and model, and a roll that is a couple of millimetres out will skip, jam or peel early. Check the size printed on the old box against the new one before you decide the gun is broken.
Work through these in order:
- Wrong size. Compare the new label size to your gun model. Sizes such as 26 x 12mm and 22 x 12mm look similar in the hand but do not swap.
- Strip not threaded. The leading strip has to sit under the guide, not beside it. Re-thread and watch it move as you squeeze.
- Cover not shut. If the catch has not clicked the roller sits too far off the strip to grip it.
- Torn leader. Tear back to a clean straight edge and start again.
- Old labels dried out. Rolls left in a hot van or a damp store lose tack and stick to the backing.
Sizes, colours and which rolls suit which gun are set out in price gun labels: sizes, colours and which fit your gun. If you are still learning the gun itself, start with how do price guns work.
How do you clear a jam or clean the gun?
Clear a jam by opening the chamber and pulling the stuck strip back out by hand rather than squeezing the trigger harder. Force is what bends the feed teeth. Once the path is clear, wipe the roller and the print head with a dry cloth, check nothing sticky is left behind, then re-thread a clean leading edge.
Adhesive residue is the usual culprit in a gun that has done a lot of work. Labels leave a thin gummy film on the roller and the strip stops gripping. A dry wipe fixes most of it. Keep the gun closed when it is not in use so dust and grit stay out of the label path.
Get the right labels for your gun
Price gun labels in every common size and colour, permanent or peelable, at trade prices with fast Irish delivery.
What should you check after loading a new roll?
Print a test label onto scrap before you go near stock. Read the figures back, check the print sits square on the label rather than running off an edge, and press the label onto a spare box to confirm it grips. Two seconds of checking saves repricing a shelf twice.
Three things show up on that test label. Faint characters mean the ink roller wants replacing. Print sitting half off the edge means the label size is not the one your gun expects. A label that lifts straight back off means peelable adhesive where you wanted permanent, or a roll that has been sitting too long.
Get into the habit of testing every time the roll changes, not just when something feels wrong. Staff who reload mid-shift are the ones most likely to skip it, and a whole delivery priced from a badly seated roll is a slow job to put right.
| Symptom | Likely cause | Fix |
|---|---|---|
| Labels come out blank | Roll loaded the wrong way round | Turn the roll over and re-thread |
| Print is faint or patchy | Ink roller worn or dry | Fit a replacement ink roller |
| Nothing feeds | Strip not under the guide, or cover not shut | Re-thread and click the cover closed |
| Labels skip or jam | Wrong label size for the gun | Check the size on the box against your model |
| Labels peel off the shelf | Peelable adhesive, or old stock | Order permanent labels or a fresh roll |
For the wider picture on guns, labels, tagging and barcode printing, see the price guns and labelling guide. If you are choosing a gun rather than a roll, 1-line vs 2-line price guns covers the difference.
Frequently asked questions
How do you change price gun labels?
Open the label chamber at the back of the gun, lift the empty core off the spindle, and sit the new roll in place. Thread the leading strip under the guide roller and out through the front slot, close the cover until it clicks, then squeeze the trigger a few times to feed the first label through.
Which way does a price gun label roll go in?
The labels face up as they pass the print head, with the backing paper underneath. Hold the roll so the strip unwinds off the top and the label side points towards the ink roller. Loaded the wrong way round the gun still feeds, but it prints on the backing and every label comes out blank.
Why is my price gun printing blank labels?
Nearly always the roll is in the wrong way round, so the head is printing on the backing paper instead of the label. Take the roll out, turn it over and thread it again. If the print is faint rather than missing, the ink roller is worn and needs replacing instead.
Why will my price gun not feed labels?
Check the label size first, as a roll that does not match your gun model will skip or jam. Then check that the strip is threaded under the guide rather than beside it, that the cover has clicked shut, and that the leading edge is clean and straight rather than torn.
How do you clear a jam in a price gun?
Open the label chamber and pull the stuck strip back out by hand. Do not squeeze the trigger harder, as force bends the feed teeth. Wipe the roller and print head with a dry cloth to lift any adhesive residue, then thread a clean straight leading edge and test a few labels.
How often do you need to change price gun labels?
As often as the roll runs out, which in a busy shop can be within a single stock intake. Most guns show the roll through a window or a gap in the chamber, so glance at it before a big delivery rather than discovering it empty halfway down an aisle. Keep a spare roll where the gun lives.
