Thermal Paper Rolls for Star TSP100, SAM4s and Citizen Printers
Star, SAM4s and Citizen receipt printers take 80 x 80mm thermal rolls on a 12.7mm core, the same standard roll as most modern tills. The main exception is Star's impact models, such as the SP700 kitchen printer, which need 76mm bond paper and an ink ribbon instead of thermal.
What size thermal roll does a Star TSP100 take?
A Star TSP100 takes an 80 x 80mm thermal roll on a 12.7mm core. That is the standard receipt roll used across the whole Star TSP range, including the TSP143, TSP650 and TSP700. The roll is 80mm wide, 80mm in diameter, and needs no ink, ribbon or toner.
The TSP100 and TSP143 are familiar sights on shop and cafe counters, and they are both thermal. You drop the roll in the bay, close the lid and print. Nothing else to buy. If you want a roll that lasts longer between changes, look at the diameter rather than the width. The width has to stay at 80mm, but a larger diameter simply holds more paper.
- Star TSP100 and TSP143: 80 x 80mm thermal, 12.7mm core.
- Star TSP650 and TSP700 (thermal): 80 x 80mm thermal, 12.7mm core.
- Star SP700 (impact): 76mm bond paper plus an ink ribbon, not thermal.
Which till rolls do SAM4s machines take?
SAM4s receipt printers take 80 x 80mm thermal rolls, the same as Star and Epson thermal models. Older SAM4s cash registers are the thing to watch. Some of those ECR units were built for a narrower roll, usually 57mm or 76mm, so check the paper bay before you order a full box.
SAM4s is a familiar name on Irish counters because the brand covers both modern touchscreen tills and older push-button cash registers. The modern units print thermal at 80mm. The older registers can be either thermal or bond, and can be narrower. The fastest check is the roll already sitting in the machine. Pull it out, look at the paper width, and scratch the shiny side with a coin. A grey mark means thermal.
What rolls fit Citizen receipt printers?
Citizen receipt printers take 80 x 80mm thermal rolls on a 12.7mm core. Citizen builds thermal counter printers and mobile units, and the counter models use the same standard 80mm roll as Star and SAM4s. Narrower Citizen mobile and kiosk printers can take a smaller thermal roll instead, so confirm the width on the unit.
There is nothing special about a Citizen roll. Once the width and core match, any good 80mm thermal roll prints cleanly. Buying the correct width matters far more than buying a brand-badged roll.
Star, SAM4s and Citizen rolls at a glance
Use this as your starting point, then confirm against your exact model. The size is often printed on a label inside the paper bay.
| Printer or till | Roll it takes | Notes |
|---|---|---|
| Star TSP100 / TSP143 | 80 x 80mm thermal | The most common Star counter printers |
| Star TSP650 / TSP700 (thermal) | 80 x 80mm thermal | Standard hospitality EPOS printers |
| Star SP700 (impact) | 76mm bond, often 2-ply | Kitchen docket printer, needs an RC700 ribbon |
| SAM4s receipt printers | 80 x 80mm thermal | Same roll as the Star TSP range |
| SAM4s older ECR registers | 57mm or 76mm | Check the bay, some are bond not thermal |
| Citizen receipt printers | 80 x 80mm thermal | Mobile and kiosk units can take a narrower roll |
Which of these printers need bond paper and a ribbon?
Only the impact models. The Star SP700 is a dot-matrix kitchen printer, so it prints by striking an ink ribbon against plain bond paper. Put a thermal roll in it and nothing prints. It takes 76mm bond rolls, often 2-ply so the kitchen keeps a copy, plus an RC700 ribbon.
Impact printers are still common at the pass because ribbon printing survives heat and steam better than a thermal receipt. If that is your setup, order the ribbon at the same time as the paper. Printing fades slowly, so a worn ribbon is easy to miss until a docket comes out blank. The full ribbon list is in ink ribbons explained, and the difference between the two paper types is set out in bond rolls vs thermal rolls.
How do you check what your own machine takes?
Check three things in order. Look at the box your last rolls came in, because the size is printed on it. If the box is gone, find the model number on the printer and match it to a compatibility list. If neither works, measure the old roll: the paper width across the roll, then the roll diameter.
Then confirm the paper type with the coin test. Drag a coin or a fingernail firmly across the shiny side. A grey line means thermal. Nothing at all means bond paper, so you need a ribbon too.
Where the model number hides varies by brand, so it is worth knowing the usual spots:
- Star TSP units carry the model on a label on the underside or the rear panel, beside the cable sockets.
- SAM4s tills print the model on the front fascia, and older registers repeat it on the receipt header.
- Citizen printers tend to label the paper bay itself, so lift the lid before you go hunting underneath.
Running a different brand? The till roll compatibility guide covers every machine type, and till rolls for Epson TM printers handles the other big name behind Irish counters.
Order rolls for your Star, SAM4s or Citizen printer
80 x 80mm thermal rolls in stock by the box, plus every other common size, at trade prices with fast Irish delivery from our Cavan warehouse.
Frequently asked questions
What size thermal paper roll does a Star TSP100 use?
A Star TSP100 uses an 80 x 80mm thermal roll on a 12.7mm core. That is the standard receipt roll across the Star TSP range, including the TSP143, TSP650 and TSP700. No ink, ribbon or toner is needed because thermal rolls print with heat alone.
What till rolls do SAM4s machines take?
SAM4s receipt printers take 80 x 80mm thermal rolls, the same as most Star and Epson thermal models. Older SAM4s cash registers are the exception, as some were built for a narrower 57mm or 76mm roll and some use bond paper. Check the paper bay before ordering a box.
Do Citizen receipt printers use the same rolls as Star?
Yes, for counter printers. Citizen receipt printers take 80 x 80mm thermal rolls on a 12.7mm core, the same roll as a Star TSP100. Narrower Citizen mobile and kiosk printers can take a smaller thermal roll instead, so confirm the width printed on the unit or in its manual.
Does the Star SP700 take thermal rolls?
No. The Star SP700 is an impact printer, so it prints by striking an ink ribbon against plain bond paper. It takes 76mm bond rolls, often 2-ply so the kitchen keeps a copy, plus an RC700 ribbon. A thermal roll produces nothing at all in that machine.
Are all 80mm thermal rolls the same?
The width of 80mm and the 12.7mm core are standard, but the diameter varies, and that sets how much paper the roll holds. Any 80 x 80mm thermal roll fits an 80mm printer. Pick a larger diameter if your till is busy and you want fewer roll changes.
How do I tell if my till roll is thermal or bond?
Drag a coin or a fingernail firmly across the shiny side of the paper. Thermal paper leaves a faint grey line where the friction heats the coating. Bond paper leaves nothing, which means the printer is an impact model and needs an ink ribbon as well as the roll.
